ELECTRIC GEX 50

APPLICATION

Indoor/Outdoor Manufacturing, Warehousing & Shipping/Receiving

FEATURES

In the past, one truck would be used for outdoor applications and another truck would be used for indoor warehousing. Now one GEX can handle both environments, leaving you with the thought… two “hands” aren’t always better than one.

 

HINGED REAR CONTROL COVER

Supported on gas springs for easy service access from a standing position

ON-BOARD DIAGNOSTICS

Allow servicing mechanic to check fault codes without service tool

HIGH PERFORMANCE

Rivals IC truck performance in speed, acceleration and gradeability

MORE EFFICIENT SYSTEM

Higher voltage = lower line loss & heating = greater efficiency

BETTER SUITED TO RAPID CHARGE

Only requires one receptacle via single battery connector

INCREASED BATTERY CAPACITY

GEX 40/45/50 can accommodate 72 kwh battery

LOW CENTER OF GRAVITY

CLARK moved back the steer axle, dropped the battery compartment and moved all major components lower 

CURVE CUTBACK
Reduces truck travel speed in turns 
WIDE STANCE
Provides excellent lateral stability

FULLY ADJUSTABLE/PROGRAMMABLE

The operator can select from 4 pre-set performance modes 

ALARM CODES
Indicates the current alarm code and stores previous alarm codes for quick access 
 
PASSWORD PROTECTED
Certain adjustments can be password protected to allow only authorized operators to make adjustment

MAXIMUM VISIBILITY

Nested I-channel allows space for cylinders, hoses and chains
 
HYDRAULIC CUSHIONING VALVE
Silent staging reduces shock and vibration
 
SHIMMABLE, SEALED & CANTED ROLLERS
Carriage has 6 rollers to maximize load distribution and reduce free play

2-WHEEL DRIVE
Provides added traction, especially on wet or uneven surfaces

WILL NOT SCUFF TIRES
Inside wheel power reverses in tight turns preventing scuffing of steer tires like conventional 4-wheel trucks

HALL EFFECT STEER SENSOR
Relays steer tire position to contro

FEWER PARTS & MINIMUM WEAR = LESS DOWNTIME

Enclosed, brushless

Thermal and stall protection

Dual/powered reversing for tighter turns

Suitable for Wet Applications

Same motors for E & EE

THREE FORMS OF REGENERATIVE BRAKING
Accelerator release (Proportional to accelerator position)

Change of direction (Proportional to accelerator position)

Service brake (Foot brake)

WET DISC BRAKES
Enclosed and oil cooled for smooth, quiet operation

Built with long life lining material

Less downtime

ELECTRIC TMX15

APPLICATION

Manufacturing, Warehousing, Bottling & Shipping/Receiving

FEATURES

The TMX continues the evolution of our three-wheel design with the efficiency, low maintenance and power of a 100% AC System. This rugged yet comfortable design delivers superior capacities and the quality, dependability and maneuverability you’ve come to expect from CLARK; the inventor of the three-wheel forklift.

 

FEWER PARTS & MINIMUM WEAR = LESS DOWNTIME = HIGHER ROI
Enclosed, brushless smart lift lock out

Thermal & stall protection

One motor for both steering and hydraulics

NO BRUSHES TO CHANGE OR COMMUTATOR TO TURN…EVER
HEAVY DUTY, HIGH TORQUE DRIVE MOTOR
Produces twice the draw bar pull of some competitors

Climbs grades previously limited to IC trucks

STALL PROTECTION
13% INCREASED RUNTIME OVER DC EQUIVALENT
Standard battery compartment accommodates a 1240 AH battery

Optional battery compartment available for a full 1550 AH battery

ADDED STRENGTH
The standard single-tire steer axle and an optional dual-tire steer axle are made from high strength cast steel and heat treated for additional strength

QUIET, DEPENDABLE OPERATION
Incorporates spiral bevel and helical gear sets

Design has over 20 million field hours in heavy-duty application

COMPLETELY CUSTOMIZE PARAMETERS TO OPERATOR’S PREFERENCE
Acceleration rate, decelaration rate and separate FW/RV max speed

FULLY PROGRAMMABLE
Lift speed is fully proportional to lift lever position

PROGRAMMABLE SPEEDS
Tilt and auxiliary functions run at programmable fixed speeds

FULLY PROGRAMMABLE
Up to 20 performance parameter settings such as acceleration, creep speed and regen braking rate can be adjusted to meet your requirements

SPEED LIMITING
Maximum travel speed can be programmed, forward and reverse can be set independently

CONTROLLED DESCENT
Controller senses movement – no accelerator pedal input = drive motors apply counter torque allowing the truck to slowly descend an incline in a controlled manner

RAMP START
Added torque eliminates roll back when starting on an incline

MAXIMUM VISIBILITY
Nested I-channel allows space for cylinders, hoses and chains

HYDRAULIC CUSHIONING VALVE
Silent staging reduces shock and vibration

SHIMMABLE, SEALED & CANTED ROLLERS
Carriage has 6 rollers to maximize load distribution and reduce free play

FULLY ADJUSTABLE SEAT
Molded for support with non-cinching, retractable seat belt

TILT STEERING COLUMN
Adjust to suit operator and provides easier entry/exit

COWL MOUNTED HYDRAULIC CONTROLS
Located and sized for ease of use

THICK MOLDED FLOOR MAT
Reduces vibration and noise level to improve operator comfort

Electric ECX25

APPLICATION

Manufacturing, Warehousing, Bottling & Shipping/Receiving

FEATURES

The CLARK ECX series of electric lift trucks is the ideal choice for demanding manufacturing and distribution applications. Superior ergonomic design, operator comfort, safety and outstanding truck performance are backed by the oldest name in lift trucks.


FEWER PARTS & MINIMUM WEAR = LESS DOWNTIME = HIGHER ROI
Enclosed, brushless smart lift lock out

Thermal & stall protection

One motor for both steering and hydraulics

NO BRUSHES TO CHANGE OR COMMUTATOR TO TURN…EVER
HEAVY DUTY, HIGH TORQUE DRIVE MOTOR
Produces twice the draw bar pull of some competitors

Climbs grades previously limited to IC trucks

STALL PROTECTION
THREE FORMS OF REGENERATIVE BRAKING
Returns energy into the battery

MAXIMUM PROTECTION

Dual action steer cylinder and fittings are protected while allowing easy access to the components

ONE-PIECE HOUSING
The CLARK ED30 reduces the possibility of leaks

SMOOTH, QUIET OPERATION
Utilizes durable helical gears

COMPLETELY CUSTOMIZE PARAMETERS TO OPERATOR’S PREFERENCE
Acceleration rate, decelaration rate and separate FW/RV max speed

PARKING BRAKE REMINDER
Sounds alarm if operator does not set parking brake

BACK LIT LCD
Auto on with key switch and provides excellent visibility in direct sunlight

BATTERY STATE OF CHARGE AND TRAVEL SPEED DIGITAL GAUGE
10-segments used to display remaining charge and programmed speed

FULLY PROGRAMMABLE
Up to 20 performance parameter settings such as acceleration, creep speed and regen braking rate can be adjusted to meet your requirements

SPEED LIMITING
Maximum travel speed can be programmed to your requirements and if necessary, forward and reverse can be set independently

CONTROLLED DESCENT
When the controller senses movement but no accelerator pedal input, it signals the drive motors to apply counter torque allowing the truck to slowly descend an incline in a controlled manner

RAMP START
Added torque eliminates roll back when starting on an incline

MAXIMUM VISIBILITY
Nested I-channel allows space for cylinders, hoses and chains

HYDRAULIC CUSHIONING VALVE
Silent staging reduces shock and vibration

SHIMMABLE, SEALED & CANTED ROLLERS
Carriage has 6 rollers to maximize load distribution and reduce free play

FULLY ADJUSTABLE SEAT
Molded for support with non-cinching, retractable seat belt

TILT STEERING COLUMN
Adjust to suit operator and provides easier entry/exit

COWL MOUNTED HYDRAULIC CONTROLS
Located and sized for ease of use

THICK MOLDED FLOOR MAT
Reduces vibration and noise level to improve operator comfort

Walkie WPX45

APPLICATION

Manufacturing & Warehousing

FEATURES

ERGONOMIC STEER/CONTROL HANDLE

Solid steel tubing – Solid steel tubing arm and handle designed to outlast cast aluminum or plastic designs

Operator Control – Handle offers travel, lift and lower functions all accessible without the operator having to lift a hand from the handle

Angle grips – Designed to allow easy operation with either hand

Wrap around steel guard – Reversing switch, thumb control, and horn are standard

Minimum steering effort – Low mounted tiller arm offers excellent operator comfort

Gas assisted spring handle – Gently returns handle to vertical position

Crawl speed function – With the steer handle at 5° back-tilt from vertical position operator has ease of use in tight areas

Optimized gear technology – State of the art optimized gear technology supplies advantages such as low noise level, high efficiency and high performance

Drive motor mount – Vertical drive motor is directly mounted to the gear housing increasing component life

Drive train – Oil bathed hypoid bevel gear drive train with tapered roller bearings transfers power to the axle

Solid steel tubing – Solid steel tubing arm and handle designed to outlast cast aluminum or plastic designs

Operator Control – Handle offers travel, lift and lower functions all accessible without the operator having to lift a hand from the handle

Angle grips – Designed to allow easy operation with either hand

Wrap around steel guard – Reversing switch, thumb control, and horn are standard

Minimum steering effort – Low mounted tiller arm offers excellent operator comfort

Gas assisted spring handle – Gently returns handle to vertical position

Crawl speed function – With the steer handle at 5° back-tilt from vertical position operator has ease of use in tight areas

Electromagnetic Brake

Mounted on the motor armature shaft multiplying the braking power through the transmission

Top-Mounted Brake

Design keeps brake away from dirt and debris.

Parking brake is automatically applied when truck stops and handle is released

System features anti-roll back and neutral braking

24-Volt AC Inverter – Travel control with matching drive motor provides high performance throughout the entire speed range

Travel Speed – Remains constant relative to throttle position regardless of load-neutral braking offers predictable performance

Additional Features – Separately fused power control circuits, quick disconnect EPD power cut off, hour meter/battery discharge indicator combination gauge and lift lock out complete the system

Walkie WP30

APPLICATION

Light Manufacturing, Grocery & Delivery Trucks

FEATURES

DRIVE MOTOR – 24-Volt permanent magnet DC drive motor increases efficiency and duty cycle

BRAKES – Parking brake is automatically applied when truck stops and handle is released

HYDRAULIC SYSTEM – Lift cylinder has durable, chrome-plated lift rod provides smooth lifting and lowering

STANDARD BATTERY – 70Ah (AGM) Absorbed Glass Mat battery pack for extended run times – up to 4.5 hours

ON-BOARD CHARGER – Standard 110V three-prong outlet plug for convenient charging

STANDARD EQUIPMENT – Quick disconnect EPD power cut-off, hour meter, and battery discharge indicator all come standard

DRIVE MOTOR – 24-Volt permanent magnet DC drive motor increases efficiency and duty cycle

BRAKES – Parking brake is automatically applied when truck stops and handle is released

HYDRAULIC SYSTEM – Lift cylinder has durable, chrome-plated lift rod provides smooth lifting and lowering

STANDARD BATTERY – 70Ah (AGM) Absorbed Glass Mat battery pack for extended run times – up to 4.5 hours

ON-BOARD CHARGER – Standard 110V three-prong outlet plug for convenient charging

STANDARD EQUIPMENT – Quick disconnect EPD power cut-off, hour meter, and battery discharge indicator all come standard

Solid steel tubing – Solid steel tubing arm and handle designed to outlast cast aluminum or plastic designs

Operator Control – Handle offers travel, lift and lower functions all accessible without the operator having to lift a hand from the handle

Angle grips – Designed to allow easy operation with either hand

Wrap around steel guard – Reversing switch, thumb control, and horn are standard

Minimum steering effort – Low mounted tiller arm offers excellent operator comfort

Gas assisted spring handle – Gently returns handle to vertical position

Crawl speed function – With the steer handle at 5° back-tilt from vertical position operator has ease of use in tight areas

Removable one piece power head cover allows for easy maintenance

Walkie CJ55

FEATURES

Standard features are the same on our complete line of Pallet Jacks unless otherwise noted.

Rugged heavy duty frames of steel, galvanized steel or stainless steel are constructed of one-piece formed channel, offer light weight and strength.
Heavy Duty Jacks feature reinforced gussets and reinforced bulkhead headers which provide increased strengthened piston seat.

Rugged heavy duty frames of steel, galvanized steel or stainless steel are constructed of one-piece formed channel, offer light weight and strength.
Heavy Duty Jacks feature reinforced gussets and reinforced bulkhead headers which provide increased strengthened piston seat.

Quality design pumps complete with a special lowering valve allow controlled rate of descent, and an overload bypass valve.
Galvanized Jacks have Galvanized pumps and Stainless Steel Jacks have Stainless pumps. The Heavy Duty Jack pump is leak proof with overload capacity. The maintenance free pump features a hard chrome plated lift cylinder & piston, quality polyurethane seals & wipers, and an easy to remove cartridge design. A unique Pump Piston Dust Cover prevents damage to the top seal from dust and debris. New additional foot release pedal provides operation versatility.

Featuring a reinforced base, the spring-a-matic handle returns to the upright position automatically.
The Heavy Duty Jack has a tapered handle for greater strength.

Control handles have three position (raise/neutral/ lower) fingertip controls which are ergonomically designed and free of pinch points.
The Heavy Duty Jack is designed for left or right hand operators.

Standard trucks require 10 strokes to raise forks to maximum lift.
The Heavy Duty Jack requires 13 and the Quick lift which when in “quick lift” mode, only requires 5.

200 degree pivot action allows greater maneuverability with 7” polyurethane wheels, sealed bearings and “ball-thrust” steering.
The Low Profile Jacks have 6” wheels and the Heavy Duty Jacks have an articulating axle which allows for level transport of loads on uneven floors.

2.9” polyurethane rollers with sealed bearings are standard. 
The Low Profile Jacks have 2” rollers, and the Weigh Scale Jacks have 2.75” rollers.

Adjustable push rods allow for individual adjustment capability of either fork height.

One piece hangers are constructed of Cast Iron for greater strength and longevity while Galvanized are coated and Stainless Steel are made of stainless.

There are grease fittings and bushings at all pivot points for easy maintenance. The Heavy Duty Jacks utilize self lubricating high impact bushings and lubrication fittings at all pivot points for improved maintenance capabilities.

Four additional helper rollers for easy exit and entry of pallets on all but Low Profile and 4 Way Jacks